UISP Router and Console 5.5.0 includes the following improvements and bugfixes.

Improvements

• [UISP Console] Updated the bundled UISP application to version 3.0.159.
• Upgraded many underlying software packages to newer versions for improved security and performance.
• Added support for DHCP relays: DHCP -> DHCP Relays.
• Firewall Groups of type "Port" now accept port ranges: Firewall -> Groups -> Add Group -> Type: Port -> Port.

Bugfixes

• [UISP Router Pro] Fixed an issue where changing the link speed to a fixed value failed on SFP+ ports when no SFP module was inserted.
• [UISP Router Pro] Excluded dropped pause frames from the "Rx Dropped" counter to avoid misleading drop statistics.
• Fixed an error on the System Settings page that appeared when the DNS Forwarder service had never been configured.
• Removed the "Both" option from the IP Version selector for DNAT and SNAT rules: Firewall -> NAT -> Postrouting/Prerouting -> Add Rule -> IP Version.
• Fixed an issue where the firewall rule tooltip could overlap and block the button for adding a new rule.
• Fixed an issue where the "Save" button would appear on the settings pages even when no actual changes had been made.

Known issues

• Limited options for configuring the internet connection in the Local Web Setup Wizard. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 3.0.159 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.
• Feedback is welcome -- if you encounter an issue or are unsure about any behavior, please let us know in the thread below this post.

UISP Router and Console 5.4.2 includes the following improvements and bugfixes.

Improvements

• [UISP Console] Updated the bundled UISP application to version 3.0.151.
• Added support for loopback interface configuration.
• Added local and remote authentication ID support for IPsec connections.
• Dynamic routes can now be preferred over standard routes by modifying their distance. E.g., default gateway route via OSPF will be preferred over DHCP, if the distance of the DHCP route is set higher than 110.
• System logs now use the updated timezone.

Bugfixes

• Fixed incorrect hostnames displayed in DHCP static leases table.
• Fixed DHCPv4 failing on Windows clients when using an empty domain name.

Known issues

• Limited options for configuring the internet connection in the Local Web Setup Wizard. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 3.0.151 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPS port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.

UISP Router and Console 5.4.1 includes the following improvements and bugfixes.

Improvements

• [UISP Console] Updated the bundled UISP application to version 3.0.147.
• Added hints to port forwarding interface to display currently used ports to prevent conflicts.
• Implemented Maximum Segment Size (MSS) clamping for enhanced network performance.
• Added direction information to firewall rulesets for improved clarity.
• Added ability to edit system timezone settings.
• Increased memory limits for neighbor checking and DHCP server to improve stability and performance.

Bugfixes

• Fixed IP addresses being sorted as strings instead of numerical values in DHCP Leases.
• Fixed missing error messages when attempting to remove interface that can't be removed.
• Fixed IPv6 PD interface selection showing current interface when DHCPv6 is configured.
• Fixed DHCP server incorrectly rejecting valid IP addresses within configured ranges.
• Fixed upgrade process incorrectly marking user-aborted upgrades as failures.
• Fixed static DNS servers being removed when disabling dynamic ones.

Known issues

• Limited options for configuring the internet connection in the Local Web Setup Wizard. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 3.0.147 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPS port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.

UISP Router and Console 5.4.0 includes the following improvements and bugfixes.

Improvements

• [UISP Console] Updated the bundled UISP application to version 2.4.206.
• [UISP Console] Added backup integrity verification to improve reliability during backup restoration.
• Upgraded many underlying software packages to newer versions for improved security and performance.
• Improved descriptions in various sections of Local Web Interface (e.g., VPNs, OSPF).
• Added IGMP proxy service configuration: Services -> IGMP Proxy.
• Introduced support for GRE and IPIP tunnel interfaces: Dashboard -> Interfaces -> Add Interface -> Tunnel.
• Enhanced OSPF configuration with multiple new capabilities:
• Added the ability to assign networks via interface selection: Routing -> OSPF -> Add OSPF Area -> Type -> Interface.
• Added support for setting network types and more interval parameters: Routing -> OSPF -> Add OSPF Interface.
• Added neighbor configuration for non-broadcast network scenarios: Routing -> OSPF -> Add Neighbor Configuration.

Bugfixes

• Fixed an issue where SD cards would not mount properly when formatted on 5.1.0 firmware or newer but used on an older firmware than 5.1.0.

Known issues

• Limited options for configuring the internet connection in the Local Web Setup Wizard. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.206 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.

UISP Router and Console 5.3.2 includes the following improvements and fixes.

Improvements

Local Web Interface

• Introduced the option to configure SSH keys: Settings → SSH → SSH Keys or Top Navigation Bar → <username>.
• Added support for setting the routing ECMP hash policy: Routing → Settings.
• Enabled starting, stopping, or restarting the UISP application: Dashboard → UISP Application → (i).
• Added a feature for adjusting firewall connection state timeouts: Firewall → Firewall Settings.
• Added support for configuring DHCPv6/PD settings:
• Configure a WAN interface to receive an IPv6 prefix: Dashboard → Interfaces → <WAN Interface> → DHCPv6.
• Set up a LAN interface to delegate the received IPv6 prefix: Dashboard → Interfaces → <LAN Interface> → DHCPv6 Prefix Delegation.
• Create an IPv6 DHCP server on the configured LAN interface to assign addresses to LAN clients: DHCP → DHCP Servers → Add Server → IPv6.
• Improved IPv6 support by assigning a WAN address derived from IA_PD when IA_NA is not provided by the ISP.

Bugfixes

• [UISP Console] Addressed an issue where port flapping occurred due to incompatible or missing support for Energy Efficient Ethernet (EEE) on the peer device.
• Fixed an issue where custom PPPoE interface names were not properly restored after a device reboot.

Known issues

• Limited options for configuring the internet connection in the Local Web Interface setup wizard. As a workaround, use the mobile app or skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.155 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.

UISP Router and Console 5.3.1 includes the following improvements and fixes.

Improvements

• Added TCP MD5 signature option support to be able to use neighbor PEER password PASS in BGP config.
• Optimized connection tracking by defining reduced timeouts to prevent packet drops caused by a full conntrack table.
• Added the option to redistribute BGP routes into OSPF settings.
• Added support for configuring ICMP(v6) type in firewall rules.

Bugfixes

• Fixed an issue causing high CPU usage in the network discovery process in large-scale networks.
• [UISP Router Pro] Resolved locking issues leading to configuration failures and system instability.
• [UISP Router Pro, UISP Console] Resolved a rare eMMC detection issue that could cause the device to get stuck during a software reboot.
• Resolved an IP accounting issue that could trigger unexpected device restarts.

Known issues

• Limited options for configuring the internet connection in the Local Web Interface setup wizard. As a workaround, use the mobile app or skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.155 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.

UISP Router and Console 5.2.0 includes the following improvements and fixes.

Improvements

• The default version of the UISP application on UISP Console devices has been updated to 2.4.155.
• The Docker CLI on UISP Console devices has been updated to match the version of the Docker Engine.
• Enabled support for multiple equal-cost paths in dynamic routing, allowing non-deterministic path selection for matching packets.
• DNS Forwarder's Host Overrides in the Local Web Interface now support wildcard domains.
• Improved WireGuard VPN server configuration in the Local Web Interface. Clients can now scan a QR code or download the configuration directly.

Bugfixes

• Fixed an issue in the Local Web Interface where a switch port could not be set to stand-alone mode if tagged VLANs were assigned to it.
• Fixed a performance issue in QoS queue provisioning.

Known issues

• We've identified an issue with the Geomagnetism module in the UISP application. The fastest way to hotfix the issue is to update the version to 2.4.155 or newer. Here are guides on how to apply the fix on UISP Console platform.
• UISP Console with SSH access: SSH into the device's CLI and run /mnt/ssd/unms/app/unms-cli update.
• UISP Console without SSH access:
• Make sure you have a backup of your UISP Console application on your SD card (please note that the SD card uses the ext4 filesystem).
• Please ensure that your UISP mobile app is the latest possible version.
• Perform a factory reset of the device. This will delete all data, so a good backup is critical.
• Use the UISP mobile app to go through the initial wizard.
• When the firmware upgrade is offered, you need to update your UISP Console to the latest firmware version 5.2.0. This is a critical step to prevent the infinite preparing status!
• When asked for a hostname, the UISP Console, use the same one that you have now.
• Restore the backup from the SD card or upload the backup file from an external file system and then restore it from the UISP GUI.
• If this process does not help, please try it once more. It should work the second time.
• Limited options for configuring the internet connection in the Local Web Interface setup wizard. As a workaround, use the mobile app or skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the Local Web Interface.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.155 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.

UISP Router and Console 5.1.0 includes the following improvements and fixes.

Improvements

• While the device is in factory default state, it provides a captive portal for web setup.
• Improved OSPF -- more information is available for OSPF, and there are more configuration options. E.g., information about OSPF neighbors is available now.
• Improved user feedback for invalid BGP configurations.
• Added the ability to power cycle PoE devices in the Local Web Interface.
• Upgraded many underlying software packages to newer versions, increasing stability and security.
• Added an option to reject default gateway and DNS servers for PPPoE interfaces.
• PPPoE interfaces can now have the username and password omitted if needed.
• The device setup process using the Local Web Interface is now faster.
• Support file creation is now faster, especially noticeable on low-performance devices.
• Added support for UACC-CM-RJ45-MG auto negotiation.
• Improved the process of setting up a DHCP server in the Local Web Interface.
• The device's firmware can now be upgraded from release update channels using the Local Web Interface.
• It is now possible to port forward a range of ports at once (e.g., ports 10000-20000) in the Local Web Interface.
• Enhanced the error message shown in the Local Web Interface when VLAN interface creation fails.
• The Local Web Interface on UISP Console devices now shows the status of the locally run UISP Application, if there is one.
• The default version of the UISP application on UISP Console devices has been updated to 2.4.143.
• Small improvements when using multiple VPNs.

Bugfixes

• Fixed setting up DHCPv6 servers in the Local Web Interface.
• SPF+ ports are now correctly labeled in the Local Web Interface (previously labeled as SFP).
• Fixed an issue in the Local Web Interface where sometimes MTU changes wouldn't apply for a Bridge interface.
• Updated IPsec to resolve reported CVE (CVE-2023-41913).
• Updated the ARP table in the Local Web Interface to display port segregation by VLANs.
• Other small Local Web Interface fixes.

Known issues

• Limited options for configuring the internet connection. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the local web interface.
• In certain syntactically incorrect BGP configurations, the user feedback describing the error will display the error messages twice.
• A switch port cannot be set to stand-alone mode while any tagged VLANs are assigned to it. As a workaround, please remove all tagged VLANs first.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.143 or newer.
• The Local Web Interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.
• The minimal password requirements for the router's local user have been increased -- now at least one numeric character is required.

UISP Router and Console 5.0.4 includes the below improvements and fixes.

Improvements

• Improved OSPF and BGP resiliency.
• Added a few hints on how to configure the firewall for IPsec site-to-site VPN in the local web interface.

Bugfixes

• Updated openssh to resolve reported CVE (CVE-2024-6387).

Known issues

For the local web setup wizard, we are aware of the following issues:

• Limited options for configuring the internet connection. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the local web interface.
• The WAN interface for NAT/Masquerade rule is not configured. Please do so in the local web interface after completing the setup.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.93 and newer.
• Due to incompatible changes in firewall settings, it is not possible to seamlessly downgrade from version 5.0.x to older 3.x releases.
• Firmware downgrade is only available from the local web interface, and the device is automatically factory reset during downgrade.
• Be sure to create a configuration backup before upgrading from firmware version 3.x or older.
• The local web interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.
• Currently, the local web setup is not supported for UISP Console. Please use the UISP mobile app instead.

UISP Router and Console 5.0.2 includes the below improvements.

Improvements

• Improved OSPF and BGP resiliency.
• Strong password requirement for local web interface setup.

Known issues

For the local web setup wizard, we are aware of the following issues:

• Limited options for configuring the internet connection. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the local web interface.
• The WAN interface for NAT/Masquerade rule is not configured. Please do so in the local web interface after completing the setup.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.93 and newer.
• Due to incompatible changes in firewall settings, it is not possible to seamlessly downgrade from version 5.0.2 to older 3.x releases.
• Firmware downgrade is only available from the local web interface, and the device is automatically factory reset during downgrade.
• Be sure to create a configuration backup before upgrading from firmware version 3.x or older.
• The local web interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.
• Currently, the local web setup is not supported for UISP Console. Please use the UISP mobile app instead.

UISP Router and Console 5.0.1 adds local web interface support, BGP dynamic routing, and VPNs.

Dashboard

• View the port table, throughput statistics and port utilization.
• Add VLANs, PPPoEs, and configure switch ports.
• Configure port settings such as PoE, IP Addresses and MTU.
• View detailed traffic statistics and connected devices.

Firewall

• Configure firewall rulesets and add firewall rules.
• Add source and destination NAT rules.
• Configure groups that link to firewall and NAT rules.

Routing

• View the IPv4 and IPv6 routing table.
• Add IPv4 and IPv6 static routes.
• Configure OSPF areas and interfaces.
• Configure BGP in FRR BGP format.

DHCP

• Add one or more DHCP servers.
• View the DHCP lease table.
• Configure static/fixed DHCP leases.

VPN

• Configure IPsec Site to Site VPN.
• Configure WireGuard Server VPN.

Settings

• Configure features such as NTP, and Syslog.
• Backup, restore, download support file, locate and upgrade the router.

Tools

• View the ARP table and other discovered devices.
• View detailed information of devices such as the IP address, MAC address and hostname.
• Ping connected devices or a specific IP address or hostname.
• View system logs.

Improvements

• The local web interface can be accesses either at https://uisp.lan:443 from any LAN port or via remote access from the UISP application.
• The local web interface also provides the device setup.
• The default version of the UISP application on UISP Console devices has been updated to 2.4.93.

Bugfixes

• Fixed the routing table to accept DHCPv4 option 121.
• Control groups hierarchy enabled on first boot after factory reset for UISP Console.
• Fixed the following security vulnerabilities: CVE-2023-6779, CVE-2023-6780, CVE-2023-48795, CVE-2023-50387, CVE-2023-50868.

Known issues

For the local web setup wizard, we are aware of the following issues:

• Limited options for configuring the internet connection. As a workaround, skip the internet connection setup in the wizard and configure enhanced options (PPPoE, VLANs, WAN port selection) in the local web interface.
• The WAN interface for NAT/Masquerade rule is not configured. Please do so in the local web interface after completing the setup.

Additional information

• This release is not compatible with UISP Application 2.3.x and older. Please use version 2.4.93 and newer.
• Due to incompatible changes in firewall settings, it is not possible to seamlessly downgrade from version 5.0.1 to older 3.x releases.
• Firmware downgrade is only available from the local web interface, and the device is automatically factory reset during downgrade.
• Be sure to create a configuration backup before upgrading from firmware version 3.x or older.
• The local web interface of the UISP Console is accessible on the standard HTTPs port (443) by default.
• If the UISP Application is running on the UISP Console, it uses port 8443.
• Currently, the local web setup is not supported for UISP Console. Please use the UISP mobile app instead.